Top Above Ground Pool Dismantling Reasons

above-ground-pool-dismantlingAbove ground pool dismantling is hard work. Make no mistake about it, if you need to take down an above ground pool, you’re in for a whole lot of labor. But, it doesn’t require special skills. However, it’s something best left to a professional service. Because, it’s not just dismantling which is difficult. It’s also the disposal which isn’t exactly easy or simple.

Top Above Ground Pool Dismantling Reasons

If an above ground pool structure fails, there’s a possibility you’ll have to also deal with a flooded basement. But, it might not come to that. However, it’s important to know the condition of your above ground pool for the sake of safety, at the very least. Furthermore, you should also continually monitor the amenity to know when it’s time to take it down.

During the hotter parts of summer, homes with a pool are often the envy of the neighborhood. Round above ground swimming pools are versatile because they can be taken down and moved or stored when not in use, but knowing where to start disassembling the pool and in which order the pieces should come off can be a challenge. A good rule of thumb to follow is to take the pool apart in the opposite order you put it together. If you didn’t put the pool together, taking a round above ground pool down is not difficult. —San Francisco Gate

The reason for this, is because it will create a huge mess. And, that’s a scenario you definitely want to avoid, if possible. After all, you don’t need another big clean up job. Plus, you need to protect your lawn and landscaping. While there are several reasons to take down an above ground pool, only a few are unavoidable. Here are the top above ground pool dismantling reasons to know:

  • Liner discoloration. A discolored liner can mean many things. Among them are mold and mildew, as well as an off pH balance. But, you don’t know unless you test the water and/or look directly at the liner itself. Material corrosion is another reason for liner discoloration.
  • Torn or separating liner. A torn or separating liner is a strong indication there’s something seriously awry. This can be due to a shift in the walls or the entire pool settling further into the ground.
  • Material corrosion. Eventually, the construction materials of an above ground pool will show signs of decay, it’s only a matter of time. When you see corrosion and/or rust, it means it’s nearing the end of its life.
  • Buckling walls. Walls buckling or leaning in or out are bad signs. It means the whole structure is somehow compromised and it likewise means, it’s time to dismantle it for good.

If you need an above ground pool dismantle job done, just phone 800-433-1094 or visit Haul Junk Away.

Basic Water Heater Removal Steps

water heater removalWater heater removal isn’t all that difficult. But, it does require the use of some basic tools. However, this doesn’t mean it isn’t a DIY project, although it does mean you’ll need to be a bit handy. If you’re not particularly handy and don’t understand the basics about electrical wiring and plumbing, call a professional.

When to Remove a Water Heater

Now, just like when it comes time to remove the hot tub, this is pretty much the same thing. Even though the two are constructed differently and have varying functions, the basic principles remain the same. So, when is it actually time for a water heater removal? Well, that depends on three factors: use, condition, and age.

Hot water tanks are anchored by straps or strips of perforated metal called plumber’s tape. These anchors, usually secured to wall studs behind the water tank, keep the tank secure in case of an earthquake. The straps must be disengaged and the gas line and water line shut off before the tank can be removed. The job is fairly simple and is easily accomplished with the proper tools. —San Francisco Gate

The average lifespan of a water heater is about 10 to 12 years. Some of these will last up to 15 years but not all will. Look at the serial number on the water heater. The first four numbers generally reveal the month and year of manufacturing date. For instance, 0904 likely means September of 2004, about 13 years old.

Basic Water Heater Removal Steps

If the water heater isn’t producing hot water, there’s water leaking from the appliance, it’s channeling discolored water, or is rusted, it’s probably time to go. Here are the basic water heater removal steps to take:

  • Shut off the power. Always turn off the power supply when doing any kind of home improvement. Regardless if it’s powered by electricity or gas, do not work on any appliance that’s still connected to its power supply.
  • Drain the reservoir tank . Fasten a garden hose to the drain line, located near the bottom. Open the drain valve and let the water inside the tank to empty out. This can take several minutes. Once drained, disconnect the hose and proceed to the next step.
  • Disconnect the water supply. Now, it’s time to remove the water supply from the appliance. There is one incoming line and two outgoing lines (cold and hot house supplies). If you don’t know how to do this, call a pro for help.
  • Remove the water heater. Get someone to help you take the water heater from its installation space. Even though the tank is empty, it will still be very heavy, so do this with caution to avoid injury.

Once you have the water heater disconnect and removed from the space, just phone 800-433-1094 or visit Haul Junk Away. We’ll save you the time, effort, and frustration of disposing the water heater so you can get right to replacing it to get hot water back in your home. Like water damaged furniture, it won’t be easy to rid yourself of, so we’ll do it for you.

Here’s How to Do a Storage Unit Cleanout and Make Money

storage unit cleanoutA storage unit cleanout is all about organization. When it’s time to jump in and get all your stuff out, it’s time to do it with a workable plan. Too many renters make the process more difficult and time consuming that it must be but with just a little forethought, it’s a less stressful event.

Here’s How to Do a Storage Unit Cleanout and Make Money

The single biggest obstacle is not having a detailed list of what’s inside. Therefore, you really don’t know what’s what until you delve into it. That process takes time and it also means having to separate must-keep items from those which you can do without.

Storage units are great resources when you temporarily need a place to put your things for three to six months, like you needed to do with this move. Storage units, however, are not where things should go to live for years. When you abandon things in storage units you end up spending more money storing the items than you would selling everything and buying replacement items in the future. Additionally, the storage units are much more likely to be infested with bugs, rodents, mildew, mold and other possession-ruining things than they would be in your home. —Unclutterer.com

That can seriously add to your moving stress. But, you can forego the worry when you are prepared. All you need is a few helping hands and some simple supplies to turn that stuff into cash. After all, putting some money in your pocket is a strong motivator.

Making Money through a Storage Unit Cleanout

Here’s how to turn a storage unit cleanout into a money maker:

  • Organize everything. Everything inside won’t have value. But, this doesn’t mean nothing is without value. You just need to know which items you can sell, which you can junk, and of course, what you need to keep. A little organization goes a long, long, way.
  • Learn each item’s value. Next, it’s time to separate things that you can sell. Do a little research to find what you can sell and what’s headed for the trash heap. When you price something, price it to sell quickly. Don’t worry about making a profit because that’s just not going to happen.
  • Advertise far and wide. Once you have everything priced to sell, you need to spread the word. Do this at least a week in advance. Use social media, online ads, bulletin boards, and street signs to advertise.
  • Host a storage unit sale. Instead of lugging all that stuff from the storage unit to your house, opt to host the sale right at the facility. It saves time and effort, plus you won’t have people parking in your driveway and on your street.

If you need a storage unit cleanout, phone 800-433-1094 or visit Haul Junk Away. Our crew is experienced in storage unit cleanouts and can help you.

Old Sleeper Sofa Disposal Options

old sleeper sofa disposalOld sleeper sofa disposal isn’t exactly an exciting chore but it’s eventually got to be done. The trouble with old sleeper sofa disposal is it’s not an item in high demand. In fact, it’s like dealing with an old futon sofa — trying to get rid of something without any real value. This certainly doesn’t mean you’re stuck or completely out of options.

Old Sleeper Sofa Disposal

Whether you’re converting a guest room into a playroom or just want to replace the furniture piece, you’ll quickly discover there’s not much call for an old sleeper sofa. It’s simply too personal an item in many cases and it could well be way out of style. At the very least, it’s not a hot item that people are clamoring for daily. That narrows your choices but it does mean you’ll pay hefty dump fees.

It is no secret that getting rid of a used sofa or sleeper is difficult. Upholstered furniture may not find many takers, especially when it is damaged, torn, or stained. To think that once you paid good money for a piece of furniture that now seems to be of no interest to you or anyone else. Unfortunately, with the exception of leather, upholstered furniture can depreciate greatly with use. It is difficult to get rid of it even when you are not looking to make money. —About.com

That is, unless it’s completely unusable. If this is the case, you can just call a junk removal service and save yourself the time and effort. It’s a far better option than trying to deal with it yourself. And, it won’t you to contort and wrangle to get it out of the house.

Old Sleep Sofa Disposal Options

But, if that old sleeper sofa isn’t totally out of life, you have other choices. Here’s a few helpful sleeper sofa disposal options you can use:

  • Host a garage sale. Chances are excellent that old sleeper sofa isn’t the only thing you need to get rid of in the house. So, why not take some time to put together a lot of stuff and sell it all at a garage sale? You’ll put a little cash in your pocket and free up a lot of space.
  • Sell it locally. If it’s in relatively good condition but you don’t want to go through the hassle of hosting a yard sale, place an online ad to sell it locally. Price it cheap and stipulate the buyer must pick it up and move it on their own.
  • Give it away. Also, there’s always the option to simply give it away. Tell people at work about it, put it on social media, and just generally advertise it for free. Another option is to contact a few property management services to give it away.
  • Recover and reuse it. Or, if it’s still in decent condition but needs a new look, you can always recover it. There are even sleeper sofa covers and slipcovers you can use to give it a new lease on life.

When you need an old sleeper sofa disposal, go ahead and phone 800-433-1094 or visit Haul Junk Away.

Top Self Storage Unit Cleanout Tips You can Use

self storage unit cleanoutStorage shed cleanout or storage unit cleanout are quite different. Because there is a legally binding contract with the latter, it means you can’t cut corners. It must be left in clean condition. When it comes right down to it, you’ve got to understand you’re dealing with a business. So, it’s best to do a great job to avoid being hit with additional fees.

Top Self Storage Unit Cleanout Tips You can Use

The single biggest obstacles self storage unit renters make is piling too much into the space. Over time, items add up and it becomes seriously unorganized. Then, when it comes time to do a self storage unit cleanout, it’s practically overwhelming. And, coupled with things like moving stress, it can easily become a frustrating process. But, you don’t have to feel like it’s too much. It’s really about taking a measured approach.

From the day you move your belongings into self-storage and sign the lease, a lien is in place against those items, according to Scott Zucker, an Atlanta attorney who specializes in self-storage matters. That lien lets the storage facility sell your unit’s contents to recoup what it’s owed if you don’t pay the rent. The facility can’t hold an auction right away, though. Every state has different self-storage lien laws in place but most follow a similar timeline. —SpareFoot.com

When you need to relocate or just want to stop wasting money on storing stuff, you’ll need to do a self storage unit cleanout that comports with the contractual rules. For instance, if you leave behind things, particularly something that’s considered a hazardous material, you get hit with additional fees. Even leaving personal effect behind can lead to the same. But, by following these tips, you’ll be scot-free:

  • Make a good plan. Don’t try to do this on the fly because you’ll quickly learn there’s not enough time. In other words, don’t wait until the last minute to begin the cleanout because it could easily exceed your estimate and you’ll have to race against the clock to get it all done. Give yourself at least a day or two and do so at least a week before the lease ends.
  • Get super organized. When you enter the storage space, go in with mission to organize everything. Otherwise, you’ll wind up just wandering through things and will have little to no idea what to do with this and that. Group like things together and create an inventory list.
  • Donate and sell things. Once you’re organized and know what you’re keeping and what you don’t want or no longer need, it’s time to donate and sell as much as possible. This way, you’ll have less to deal with and you’ll put some money in your pocket.
  • Keep what’s important. Now, just because you don’t really want to part with this or that doesn’t mean it’s a necessity. After all, if it’s been inside the storage space for any length of time, it’s probably not that vital. This is a great way to maximize your purge so you have fewer items to store at home.

When you need a storage unit cleanout done fast, just phone 800-433-1094 or visit Haul Junk Away.

How to Do Water Heater Removal

hot tub removalYour trusty water heater has served your household well. When you first discovered there was no hot water in the house, you immediately thought the dishwasher or washing machine used all the hot water. But, when you checked and neither was the case. Then, you checked out your water heater and thought it just had to be the heating element that’s the culprit. Turns out, that’s just not the case and now you need to know how to remove a water heater and what to do with it once you have a replacement.

How to Do Water Heater Removal

So, your water heater element seemingly went bad and you contorted yourself trying to read the model number (like you did when you had to remove the hot tub that stopped working and became an eyesore). It took many frustrating minutes to read that tiny print but you finally got it. Immediately, you rush over to the nearest home improvement store and bought the right replacement heating element. Once you returned home, you quickly turned off the power or gas, shut off the water supply, then hooked a garden hose to the drain line.

Hot water tanks are anchored by straps or strips of perforated metal called plumber’s tape. These anchors, usually secured to wall studs behind the water tank, keep the tank secure in case of an earthquake. The straps must be disengaged and the gas line and water line shut off before the tank can be removed. The job is fairly simple and is easily accomplished with the proper tools. —San Francisco Gate

Next, you drained the water heater and removed the access panel, then, unfastened the old heating element. You put in the replacement coil, replaced the access panel, unhooked the garden hose, and turned the power or gas back on. After a few hours, you turned on the kitchen faucet only to be disappointed — no hot water. You have to face the sad fact the water heater just doesn’t work any longer. Now, you’ve got to junk the water heater and install a replacement. Here’s how to remove a water heater:

  • Disconnect the power. Go to the main electrical panel and shut off the breaker to the water heater, if it’s electric. Then, you can disconnect the electrical wiring. If it’s gas, shut off the supply valve and give it several minutes before you disconnect the gas line. In addition, shut off the water supply and delivery lines.
  • Drain the reservoir tank . Though you’ve done this before just a few hours ago, you’ll have to do it all over again. Hook a garden hose to the drain valve and allow the water tank to drain completely so you can move it.
  • Disconnect the water lines. Once the water heater is drained, you’ll be able to disconnect the water lines by either unscrewing them or severing them. Be careful with severing the water lines because you’ll need to reuse these or you’ll have to patch or replace them.
  • Carefully remove the water heater. You can now carefully remove the water heater. Have a friend or family member help you out, because the appliance will be heavy and awkward to move out-of-place.

Once you have the water heater disconnect and removed from the space, just phone 800-433-1094 or visit Haul Junk Away. We’ll save you the time, effort, and frustration of disposing the water heater so you can get right to replacing it to get hot water back in your home. Like water damaged furniture, it won’t be easy to rid yourself of, so we’ll do it for you.

Old Wood Deck Restoration Made Easy

old wood deck restorationA wood deck is designed to provide a home with more outdoor entertaining space and improve backyard aesthetics. Over time, weather elements and traffic take their toll and signs of wear and tear become evident. Wood begins to crack, warp, and fade. This makes it unsightly, and, in some instances, unsafe. Warped boards can pose tripping hazards, while loose boards can come completely dislodged.

The good news is, you don’t have to be a master woodworker or skilled contractor to restore an old wood deck. All you need is some common tools and a weekend or two to bring your deck back to its former glory. Or, you can outright dismantle it and built another.

How to Do an Old Wood Deck Restoration

Before you begin the project, it’s best to be in-the-know about its real condition. Inspect it from all angles to look for mold, mildew, pest infestation, and wood rot. You’ll likely come across a few small problems, but if you find there’s significant rot, you’ll have to pull the wood out and dispose of it. If this is the case, just phone a junk hauling and removal service to do it for you. This will save time, effort, and money.

Following are some techniques you can use to give an old deck a new lease on life, or to help maintain the look of a new one. A project like this can be done in two days, but it’s best to spread the work over two weekends to ensure the wood is completely dry before you apply stain. —This Old House

Should it be in acceptable condition, enlist the help of a family member or friend. Be sure to check the weather forecast before you begin lugging all your tools and supplies out. When you are ready, simply follow these steps to restore your wood deck:

  1. Gather your tools and supplies. You’ll need a broom and/or leaf blower, drill-driver, pry bar, replacement planks or boards, eye protection, circular saw or table saw, leather gloves, screws, commercial wood deck cleaner, bucket, garden hose, scrub brushes or brooms, paint tray and roller, and latex waterproofing stain.
  2. Clear the deck off completely. Remove anything and everything from the deck. This includes furniture, outdoor decor, and anything that’s not part of the fixture. Then, sweep it off and/or use a leaf blower to clear any surface debris.
  3. Replace any boards as necessary. Next, you should begin to take-up and replace any boards that are loose, warped, or cracked. Set the damaged planks well aside to avoid tripping and use a circular saw or table saw to cut to length. Remember, measure twice and cut once and then fasten the cuts into place with screws and a drill-driver.
  4. Clean the deck with commercial cleaner. Once the replacements have been made, it’s time to clean the deck with commercial wood cleaner. Follow the manufacturer’s instructions carefully to ensure it’s cleaned properly.
  5. Seal and stain the wood to protect it. After the deck has dried, then apply a coat of latex waterproofing stain to treat and color the wood for longevity and looks. Again, follow the manufacturer’s instructions and it might be necessary to apply more than one coat.

When the latex waterproofing stain has set and dried, you can then put back any items that were previously on the deck. You’ll then be able to enjoy this refurbished deck outdoor space for many years to come! If you decide to take it down, just schedule debris clean up and have it all hauled away.

Best Ways to make More Yard Sale Money

yard sale moneyYou’ve just tried to pull into your garage and now, as many times before, realize space is seriously shrinking. It’s to the point there’s not a square inch left in the attic, the closets are ready to burst open, and, you’re simply running out of space. As you begin to rearrange things to be able to comfortably re-enter your car, you suddenly are struck by the notion that you don’t need all of this stuff. In fact, you can’t even begin to identify what’s in which boxes, or, where certain items are stuffed away.

Best Ways to make More Yard Sale Money

This is your “ah-ha” moment, and you know a garage sale is in store. It’s the perfect solution–you’ll not only free up quite a bit of space, but you’ll put some extra money in your pocket. Making it even better is the fact that you’ll actually be able to use your garage for its main purpose.

Would you like to get rid of your clutter and make some money? Garage sales (or yard sales or tag sales) are big business, even if the average selling price of goods is only 85 cents. Just multiply that by the 4,967,500 goods that are sold at garage sales each week, and the total weekly revenue that U.S. garage sales generate is $4,222,375, according to the website StatisticBrain.com. —Consumer Reports

If you want to have a successful yard sale, you don’t rush into it. That’s a great way to sabotage yourself and bring on a whole lot of frustration without much to show for your time and effort. Instead, do these things to make more yard sale money:

  • Gather stuff well before the event. One of the single best secrets of pro garage sale hosts use is to have a few dedicated boxes to toss things in for months in advance. When something of value, be it large or small, is no longer useful to you, put it in a box. Organize these as you go, so it’s easier to sort and price later on.
  • Clean it all up for the best impression. Dust, cobwebs, and other dirt is something that’s just plain icky, and, if it makes you cringe in the any way, it’s a really good bet potential buyers will feel the same. Clean everything up to make a good impression and sell stuff for more.
  • Form an alliance with neighbors. When you ban together with your neighbors, you create more of a destination because people will think it’s more likely they’ll find what they want. This also helps when you get referrals from neighbors who don’t have what someone is looking for.
  • Advertise far and wide. A yard sign and a few signs tacked to poles isn’t enough. You need to advertise online, about a week in advance, and also, in busy intersections.
  • Mark prices clearly and offer bulk deals. People will bargain for a lower price, so, sell items in bulk when you can to give them a better deal.

Another way to get a little more out of garage sale shoppers is to offer light refreshments. Some lemonade and fresh cookies are nice enticements. Just don’t make the mistake of putting refreshments out for self serve, instead, offer to pour a cup and small plate. As for the junk leftover, give us a ring and we’ll haul it away.

Clothes Dryer Replacement Made Easy

clothes dryer replacementThe convenience of major appliances makes day-to-day life a lot more simple. We often take these for granted because it’s so infrequent that we are without their function. When a clothes dryer stops working, it’s generally due to a loose, worn, or broken belt. It could also be an electrical problem. It’s also not unusual for the cost of the repairs to equal or even exceed the worth of the appliance. When this happens, it’s usually best to buy another to replace the old one, just like many other appliances.

Clothes Dryer Replacement Made Easy

Though it might seem like a simple task, replacing a clothes dryer will take a bit of time and effort. You’ll only need a few common hand tools, such as screwdrivers, wrench, duct tape, and a torpedo level, You’ll also need a helping hand to both move the old appliance out-of-place, and, to install the new one (not unlike replacing a water heater).

When you purchase a large appliance like a new washer and dryer or when you move an existing dryer, paying for professional installation can add to the cost. Instead of spending the money for a professional installation, you might consider doing the job yourself and saving the cash. —Overstock.com

When you’re ready to make the switch, gather your tools together, then, follow these steps to replace your clothes dryer:

  1. Turn off the breaker on the main electrical panel. The power to the appliance should be turned-off at the breaker so there’s no chance of electrocution. These units require a lot of power to function and you definitely don’t want to put yourself at-risk.
  2. Shut off the gas valve. If the appliance is also equipped with gas, be sure to shut it off at the valve.
  3. Disconnect the gas line. Slowly disconnect the gas line with a wrench and try not to bend it when doing so.
  4. Disconnect the electrical line. Pull the electrical power line from the wall outlet and then either duct tape it, or, if applicable, disconnect it from the appliance.
  5. Remove the exhaust tube. The exhaust tube is likely situated right behind or beside the appliance. Remove it from the appliance, leaving it attached to the wall vent.
  6. Carefully pull the dryer out of place. Along with another person, pull the dryer out. Do this carefully because it could easily damage the floor.
  7. Put the new appliance in-place. Work the new appliance in-place, also exercising caution to prevent floor damage.
  8. Connect the electrical and gas lines. Reconnect the gas and electrical lines to the new appliance.
  9. Install the exhaust tube. Connect the exhaust line to the dryer, then, work it into place carefully.
  10. Check for levelness. Place a torpedo level on top of the appliance to check for levelness. If it isn’t level, make adjustments to the legs.
  11. Turn the gas valve and electrical breaker on. Once these are on, you can then set your dryer to run to test it out.

Now that’s you’ve replaced the clothes dryer, you’ll have another task on your hands. If the old dryer doesn’t work or is damaged, you won’t be able to sell it to offset the cost of the replacement. What’s more, you’ll have to rent a truck and pay a dumping fee to get rid of it. Save yourself the time, effort, and frustration by calling a local junk hauling service to pick it up.

Steps for Removing Old Wallpaper

removing old wallpaperThere are few people who actually like wallpaper — it’s usually outdated and just down right ugly. What’s worse, it becomes discolored as it ages and peels from corners and seams. When this begins to occur, it’s typically a non-starter to try and re-adhere it to the wall. Usually, it’s time to remove it from the wall, but, that’s not as easy as it would seem. In fact, it’s generally a time consuming, frustrating trying to remove it from the surface to which has been stuck for many, many years.

Steps for Removing Old Wallpaper

Your first order of business is to identify the wall construction type: plaster or drywall. If the home is more than fifty years old, knock on the wall and listen for a hollow sound. Plaster tends to have a dull, solid sound because it’s more durable than drywall. If it’s drywall, you’ll likely hear a bit of an echo because it’s not as sturdy. The reason this is important is because if the wallpaper is adhered to drywall, you’ll have to exercise caution so not to damage it when scraping and scrubbing.

You love your house, but you cringe every time you walk by that bathroom. What were you thinking when you picked out that wallpaper? Relax, wallpaper is not forever. But, before you apply paint or a different wall-covering, you may have a little work to do. Removing old wallpaper is not that difficult. —Lowes.com

Once you’ve identified the wall construction type, you’ll need to remove everything from the walls, which includes any decor, along with switchplates and wall outlet plates. Next, clear out the entire room because practically everything will be covered with dust. Then following these steps to remove old wallpaper from the room:

  • Turn off the electrical circuit breakers to the outlets in the room. You’ll have to wet the walls substantially to remove the glue, so, shut off all circuit breakers to the wall outlets in the room to avoid any electrical problems.
  • Cover the entire area with drop cloths, particularly the flooring. Use drop cloths to cover the floor and all surfaces in the room to protect them and make cleanup a bit easier. You can also hang plastic in the doorway to minimize any broadcasting of dust and debris into other rooms.
  • Begin to peel back the wallpaper from the corners and/or separated seams. If you can grasp a corner or a split seam with your fingers, do so, and pull back very carefully. If there are no loose seams or peeled corners, use a putty knife to gently scrape under the wallpaper. Peel off as much as you can, even entire sections, if possible.
  • Use a commercial stripping solution to saturate the remaining wall paper. Follow the manufacturer’s mixing instructions and then apply the commercial stripping solution to any wallpaper that remains stuck to the surface. Give it some time to soak-in and loosen the wallpaper before peeling and scraping it off.
  • Use an abrasive scrubbing pad to remove any small remnants. There will likely be small remnants of wallpaper left behind, so, use an abrasive scrubbing pad to get it off.

Let the walls dry and then you can fill holes with spackling and let it dry. After the spackle is dry, you can then prime and paint the walls to finish the job.